CDFMH - 521-80 BLACK SILATHANE INT/EXT BRUTONE INTERIOR ALKYD SEMI-G

  • MSDS: CDFMH
  • Manufacturer: BRUNING PAINT CO INC
  • Product Name: 521-80 BLACK SILATHANE INT/EXT BRUTONE INTERIOR ALKYD SEMI-G
  • National Stock Number: 8010-00F052659
Product Identification

Product ID:521-80 BLACK SILATHANE INT/EXT BRUTONE INTERIOR ALKYD SEMI-G
MSDS Date:08/01/1993
FSC:8010
NIIN:00F052659
MSDS Number: CDFMH

Responsible Party
BRUNING PAINT CO INC
601 S HAVEN ST
BALTIMORE, MD 21224-4347
US

Emergency Phone: 410-342-3636/3641

Info Phone: 410-342-3636/3641

Cage: EO376

Contractor
KYANIZE PAINT
BALTIMORE, MD 21224 US

Telephone: 800-368-2076

Cage: 85520

Ingredients

TALC (POWDER), (ASBESTOS FREE), TALCUM; HYDROUS MAGNESIUM

CAS: 14807-96-6

RTECS: WW2710000

Fraction By Weight: 0-5%

OSHA PEL 2 MG/CUM (RESP DUST)

ACGIH TLV: 2 MG/CUM (RESP DUST)


MEDIUM ALIPHATIC NAPHTHA (AROMATIC 100), PARAFFIN-NAPTHANES

CAS: 64742-88-7

Fraction By Weight: 0-5%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM


3.32 TO 3.74 LBS/GAL

RTECS: 9999999VO


STODDARD SOLVENT (PETROLEUM DISTILLATE), MINERAL SPIRITS

CAS: 8052-41-3

RTECS: WJ8925000

Fraction By Weight: 25-50%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM

Hazards

Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:MAY CAUSE NOSE, THROAT & EYE
IRRITATION. REPEATED/PROLONGED OVEREXPOSURE TO SOLVENTS MAY CAUSE
PERMANENT BRAIN & NERVOUS SYSTEM DAMAGE.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:IRRITATION, DIZZINESS, HEADACHE, INTOXICATION,
EUPHORIA, UNCONSCIOUSNESS.

First Aid

First Aid:EYES: FLUSH W/LUKE WARM WATER FOR 15 MINS. SKIN: FLUSH WASH
W/COPIOUS AMOUNTS OF LUKE WARM WATER. INHALATION: REMOVE TO FRESH
AIR. RESTORE BREATHING IF REQUIRED. INGESTION: RINSE MOUTH
IMMEDIATELY. GI VE 6-8 OUNCES OF LIQUID. NEVER GIVE ANYTHING BY
MOUTH TO AN UNCONSCIOUS PERSON. DON'T INDUCE VOMITING UNLESS
ADVISED BY A PHYSICIAN. OBTAIN MEDICAL ATTENTION IN ALL CASES.

Fire Fighting

Flash Point Method:TCC
Flash Point:104F
Lower Limits:0.9
Upper Limits:7
Extinguishing Media:THE NFPA CLASS B EXTINGUISHER.
Fire Fighting Procedures:WATER SPRAY MAY BE INEFFECTIVE. WATER MAY BE
USED TO COOL CLOSED CONTAINERS. IF WATER IS USED, FOG NOZZLES ARE
PREFERABLE.
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE WHEN
EXPOSED TO EXTREME HEAT. DON'T APPLY TO HOT SURFACES. NEVER USE
WELDING/CUTTING TORCH ON/NEAR CONTAINER, MAY IGNITE/EXPLODE.

Accidental Release

Spill Release Procedures:STOP &/CONTAIN DISCHARGE SAFELY. KEEP SOURCES
OF IGNITION AWAY. VENTILATE AREA. USE NON-SPARKING TOOLS. COVER
W/INERT MATERIAL. KEEP OUT OF DRAINS, SEWERS/WATERWAYS. CONTACT
FIRE AUTHORITIES. NOTIFY L OCAL HEALTH & POLLUTION CONTROL
AGENCIES.

Handling

Handling and Storage Precautions:DON'T STORE >120F. DON'T CUT/PUNCTURE
CONTAINER. DON'T WELD NEAR CONTAINER. KEEP CONTAINER TIGHTLY CLOSED
WHEN NOT IN USE. USE W/ADEQUATE VENTILATION.
Other Precautions:GROUND CONTAINERS WHEN POURING & LIMIT FREE-FALL TO A
FEW INCHES. AVOID CONTAMINATED RAGS/IGNITABLE ORGANIC MATERIALS.
INTENTIONAL MISUSE BY DELIBERATELY CONCENTRATING & INHALING THE
CONTENTS MAY BE H ARMFUL/FATAL. DON'T BREATHE VAPORS/MIST.

Exposure Controls

Respiratory Protection:IN OPEN AREAS DURING SPRAY APPLICATION, USE
NIOSH/MSHA MECHANICAL FILTER RESPIRATOR/IN RESTRICTED AREAS, USE
NIOSH/MSHA APPROVED CHEMICAL MECHANICAL FILTERS/IN CONFINED AREAS,
USE NIOSH/MSHA APPROVED AIR LINE TYPE RESPIRATORS/HOODS.
Ventilation:GENERAL DILUTION/LOCAL EXHAUST TO KEEP TLV BELOW ACCEPTABLE
LIMIT DURING WELDING/FLAME CUTTING ON COATED SURFACES.
Protective Gloves:NATURAL RUBBER/NEOPRENE/BUNA N/NITRILE
Eye Protection:GOGGLES
Other Protective Equipment:APRON
Work Hygienic Practices:REMOVE/LAUNDER CONTAMINATED CLOTHING BEFORE
REUSE. WASH HANDS THOROUGHLY BEFORE EATING & USING WASHROOM.
Supplemental Safety and Health
% VOLATILE BY VOLUME: 50.96-57.73.

Chemical Properties

Boiling Pt:B.P. Text:300-416F
Vapor Pres:2
Vapor Density:>1
Evaporation Rate & Reference:SLOWER THAN BU AC
Percent Volatiles by Volume:(SUPP)

Stability

Stability Indicator/Materials to Avoid:YES
WELDING
Stability Condition to Avoid:SPARKS, OPEN FLAME, HOT SURFACES, SOURCES
OF IGNITION.
Hazardous Decomposition Products:CO, CO2 & OXIDES OF NITROGEN.

Disposal

Waste Disposal Methods:DISPOSE OF IAW/FEDERAL, STATE & LOCAL
REGULATIONS. DON'T FLUSH TO SEWER, WATERSHED/WATERWAY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.